Power Inverter without Heat Transfer: Exercise 7—Analyzing Results
This exercise describes how you analyze the results during and after the simulation. To hide CAD surfaces (not the fluid domain), switch between 
CAD Bodies and 
Flow Analysis Bodies.
CAD Bodies and Flow Analysis Bodies.Viewing the Pressure Contours on a Boundary
 | Pressure: [Pa] : Flow 101325  101314 |
1. In Boundary Conditions, under General Boundaries select POWERINVERTER_1_FLUID.
2. In the Properties panel, View tab, for Surface, set values for the options as listed below:
◦ Keep drawing—Yes
◦ Grid—No
◦ Outline—No
◦ Variable—Pressure: [Pa] : Flow
◦ Min—101314
◦ Max—101325
3. Click 
in the Graphics toolbar to display the style elements. Select Shading.
in the Graphics toolbar to display the style elements. Select Shading.Viewing Vectors on a Section
 | Pressure: [Pa] : Flow 101325  101314.75 |
1. Create a section.
2. Select Section 01.
3. In the Properties panel, Model tab, set values for the options as listed below:
◦ Type—Plane Y
◦ Position—0.006
4. In the Properties panel, View tab, for Surface, set values for the options as listed below:
◦ Variable—Pressure: [Pa] : Flow
◦ Min—101314.75
◦ Max—101325
5. In the Properties panel, View tab, for Vector, set Variable—Velocity: [m/s] : Flow
6. You can edit vector properties using the Size,Uniform Head, Head Size and Projection options.
7. In Boundary Conditions, under General Boundaries select POWERINVERTER_1_FLUID.
8. In the Functions panel click 
Turn on/off view properties and select the following from the list: 
Hide all surfaces, 
Hide all grids, and 
Hide all outlines.
Turn on/off view properties and select the following from the list: Hide all surfaces, Hide all grids, and Hide all outlines.9. Select Section 01. The vectors of this section appear.
Viewing the Streamlines in the Domain
 | Velocity Magnitude: [m/s] : Flow 2.321  0 |
1. Add Streamline01 to the Flow Analysis Tree and select it.
2. In the Properties panel, Model tab, set values for the options as listed below:
◦ Line Thickness—0.0005
◦ Animation Time Size—0.005
3. In the Properties panel, View tab, for Surface, set values for the options as listed below:
◦ Variable—Velocity Magnitude: [m/s] : Flow
◦ Min—0
◦ Max—2.321
4. In the Flow Analysis Tree, under General Boundaries select BC_00001.
5. In the Model tab, for Streamline01 set Release Particle to Yes.
Plotting the Mass Flux at the Outlet Boundary
1. In the Flow Analysis Tree, under Boundary Conditions click General Boundaries.
2. Select BC_00002.
3. Click 
XYPlot. A new entity xyplot1 is added in the Flow Analysis Tree under > > .
XYPlot. A new entity xyplot1 is added in the Flow Analysis Tree under > > .4. Select xyplot1.
5. In the Properties panel, Model tab, set the Variable as Mass Flux.
6. Click 
Stop and 
Run, if required.
Stop and Run, if required.Plotting the Pressure at Monitoring Point
1. In the Flow Analysis Tree, under Results click Monitoring Points.
2. Select Point01.
3. Click XYPlot. A new entity xyplot2 is added in the Flow Analysis Tree under > > .
XYPlot. A new entity xyplot2 is added in the Flow Analysis Tree under > > .4. Select xyplot2.
5. In the Properties panel, View tab, set Variable as Pressure.
6. Click Stop and Run, if required.
Stop and Run, if required.