The ifx_screw_data.cfg Configuration File

In the ifx_screw_data.cfg file located at <creo_loadpoint>\Common Files\afx\configuration\, you can configure the values used in the Screw Fastener Definition dialog box. See the column headings and values of the ifx_screw_data.cfg file in the tables below. Each table describes a different section of the file. When editing this file, be sure to press TAB to separate values.

In the THREAD DATA section of the ifx_screw_data.cfg file, enter the thread values for the columns DG and P. If the values are not defined in the DAT file, they are taken from here. The default value for Metric is ISO THREAD DIN 13 and for UNC, Unified Coarse Thread Series. The values described in the table below are required for the 2D preview of the thread.

THREAD DATA
Column	Value
#THREAD	The unit of the thread, either MM or INCH. This is always the first column.
DN	The fastener diameter.
DG	The drill diameter.
P	The pitch in threads per inch.

In the THREAD RUNOUT section of the ifx_screw_data.cfg file, enter the values for the additional thread depth and the thread runout. These values appear in the Side 2 – Thread, Thread depth and Drill depth lists in the Screw Fastener Definition dialog box.

THREAD RUNOUT
Column	Value
#RUNOUT	The unit of the thread runout, either MM or INCH. This is always the first column.
DN	The fastener diameter.
X	The additional thread depth
E1	The thread runout.

In the COUNTERBOREDIAMETER FOR SCREW’S section, enter the values for the counterbore diameters on the screw side. You can add your own columns. The values appear in the Side 1 – Counterbore lists in the Screw Fastener Definition dialog box. The default values are listed below:

You can preselect the columns for the screws and the washers on the screw side. Write #CBSCR <COLUMN> to the DAT file.

COUNTERBOREDIAMETER FOR SCREW'S
Column	Value
#CBSCR	The unit of the counterbore diameter for screws, either MM or INCH. This is always the first column.
DN	The fastener diameter.
<COLUMN>	The side 1 counterbore diameters.

In the COUNTERBOREDIAMETERS FOR NUTS section, enter the values for the counterbore diameters on the nut side. You can add your own columns. The values appear in the Side 2 – Counterbore lists in the Screw Fastener Definition dialog box. The default values are listed below:

COUNTERBOREDIAMETERS FOR NUT'S
Column	Value
#CBNUT	The unit of the counterbore diameter for nuts, either MM or INCH. This is always the first column.
DN	The fastener diameter.
<COLUMN>	The side 2 counterbore diameters.

In the ADDITIONAL COUNTERBOREDEPTH FOR SCREWS AND NUTS section, you can add value to your counterbore depth. If you select the Side 1 – Counterbore check box or the Side 2 – Counterbore check box, then the depth of the counterbore is calculated automatically, based on the height of the screw or nut head and the heights of the washers. Use ADD_DEPTH to add more depth so that the fastener is not flush mounted. COUNTERBOREDEPTH can be summarized in the equation below:

COUNTERBOREDEPTH = HEADHEIGHT + WASHERHEIGHTS + ADD_DEPTH

ADDITIONAL COUNTERBOREDEPTH FOR SCREWS AND NUTS
Column	Value
#ADDCB	The unit for additional counterbore depth for screws and nuts, either MM or INCH. This is always the first column.
DN	The fastener diameter.
ADD_DEPTH	The additional counterbore depth for screws and nuts.

In the MIN and MAX (Screw-in depth for screws) section of the ifx_screw_data.cfg file, enter the minimum and maximum screw-in depth. In the Screw Fastener Definition dialog box. if you click

Set length automatically or

Permanently set length automatically, the application searches for a screw length within these limits.

MIN and MAX (Screw-in depth for screws)
Column	Value
#ETSCR	The unit for minimum and maximum screw-in depth, either MM or INCH. This is always the first column.
DN	The fastener diameter.
MIN DEPTH	The minimum screw-in depth.
MAX	The maximum screw-in depth

In the MIN and MAX section of the ifx_screw_data.cfg file, enter minimum and maximum protrusion of bolt ends. In the Screw Fastener Definition dialog box. if you click

Set length automatically or

Permanently set length automatically, the application searches for a screw length within these limits.

MIN and MAX
Column	Value
#MUSCR	The unit for minimum and maximum protrusion for bolt ends, either MM or INCH. This is always the first column.
DN	The fastener diameter.
MIN DEPTH	The minimum protrusion.
MAX	The maximum protrusion.