CoCreate OneSpace Designer - Commands Reference Manual

C_LINE_INF terminate action

C_LINE_INF creates linear construction geometry using different parameters, and relations to existing elements.

Syntax


---->(C_LINE_INF)----+
                     |
    +--------<-------+    +----------------------<------------------+
    |                     |                                         |
    +--(:TWO_POINTS)------+----|posn|----+----|posn|----+----->-----+----+-->
    |                                                                    |
    |                                                                    ^
    |                     +----------------------<------------------+    |
    |                     |                                         |    |
    +--(:HORIZONTAL)------+----+----|begin posn|----+--------->-----+----+
    |                          |                    |                    |
    |                          +----|offset|--------+                    |
    |                                                                    ^
    |                     +----------------------<------------------+    |
    |                     |                                         |    |
    +--(:VERTICAL)--------+----+----|begin posn|----+---------->----+----+
    |                          |                    |                    |
    |                          +----|offset|--------+                    |
    |                                                                    ^
    |                        +----------<---------+                      |
    |                        |                    |                      |
    +--(:ANGLE)----|posn|----+----|angle posn|----+------------->--------+
    |                        |                    |                      |
    |                        +----|angle|---------+                      |
    |                                                                    |
    |                                                                    |
    |                     +------------<--------------+                  |
    |                     |                           |                  |
    +--(:ANGLE_REFERENCE)-+------|position|------+    |                  ^
    |                                            v    |                  |
    |  +---------------|angle|-------------------+    ^                  |
    |  |            |           |                     |                  |
    |  v            +----<------+                     |                  |
    |  |                                              |                  |
    |  +---|ref1 position|---|ref2 position|---->-----+---------->-------+
    |                                                                    |
    |                                                                    |
    |               +------------------------<-----------------------+   |
    |               |                                                |   |
    +--(:PARALLEL)--+----|straight element|----|offset posn|---------+->-+
    |               |                                                |   |
    |               +-|offset|-+-|straight element|-|pos for side|-+-+   |
    |                          |                                     |   |
    |                          +--------------<----------------------+   |
    |                                                                    |
    |                     +---------------------<-------------------+    |
    |                     |                                         |    |
    +--(:PERPENDICULAR)---+---|element|-------|position|------------+----+
    |                                                                    |
    |                     +---------------------<-------------------+    |
    |                     |                                         |    |
    +--(:TANGENT)---------+----|element|----+----|posn|----+---->---+----+
    |                                       |              |             |
    |                                       +----|angle|---+             |
    |                                                                    ^
    |                     +---------------------<-------------------+    |
    |                     |                                         |    |
    +--(:TWO_TANGENT)-----+----|element|----|element|---------------+----+
    |                                                                    |
    |               +-----------------------<-----------------------+    |
    |               |                                               |    |
    |               +------<------+                                 |    |
    |               |             |                                 |    |
    +--(:BISECT)----+--|fraction|-+-|1st ref posn|--|2nd ref posn|--+----+
    |               |             |                                      |
    |               +------>------+                                      |
    |                                                                    |
    |                 +-----------------<----------------+               |
    |                 |                                  |               |
    |                 +------<-----+                     |               |
    |                 |            |                     |               |
    +--(:ANG_BISECT)--+-|fraction|-+-|apex posn|----+    |               ^
                      |            |                |    |               |
                      +------>-----+                v    ^               |
                                                    |    |               |
                      +--|1st angle or ref posn|----+    |               |
                      v                                  |               |
                      +--|2nd angle or ref posn|---------+------->-------+

Options

The following options are available to create construction circles.

:TWO_POINTS - specifies 2 points that the current construction line must pass through.
:HORIZONTAL - specifies a construction line parallel to the u-axis of the active workplane's coordinate system. Specify the point or offset to define the position of the line.
:VERTICAL - specifies a construction line parallel to the y-axis of the active workplane's coordinate system. Specify the point or offset to define the position of the line.
:ANGLE - specifies a construction line at an angle with respect to the u-axis of the active workplane's coordinate system.
:ANGLE_REFERENCE - specifies a construction line with respect to a specified reference line. Enter an angle to specify the offset.
:PARALLEL - specifies a reference line the new construction line must be parallel to, and offset from.
:PERPENDICULAR - specifies a new construction line perpendicular to a reference element. If possible and necessary, the referenced elements will be extended.
:TANGENT - specifies a point on a curved element. The tangent point of the construction line is placed on the approximate tangent point on the curve. Alternatively, you can enter the angle for the line.
:TWO_TANGENT - the new construction line starts or ends at the tangent points on the curved elements.
:BISECT - the construction line bisects the line defined by two points.
:ANG_BISECT - creates a construction line which passes through your first point, and bisects the line created by your second and third points.

When to use

Use this action to create straight construction lines.

Example

The following parameter sequence creates a construction line horizontal to the u-axis of the active workplane's coordinate system.

C_LINE_INF :HORIZONTAL 75,75 150,100