CoCreate OneSpace Designer - Commands Reference Manual

C_CIRCLE terminate action

C_CIRCLE creates a construction circle defined by a center point, peripheral points, approximate tangent points, diameter or radius.

Syntax


                              +-----------------<-------------------+
                              |                                     |
-->(C_CIRCLE)--+--(:CEN_RAD)--+--|center posn|--+---|radius|--------+---+--->
               |                                |                   |   |
               |                                +---|position|------+   |
               |                                                        |
               |                            +------<-----+              |
               |                            |            |              |
               +--(:CONCENTRIC)--|element|--+--|offset|--+--------------+
               |                                                        |
               |             +-|pos|-+----->------+                     |
               |             |       v            |                     |
               +--(:RADIUS)--+--->---+--|radius|--+--|center posn|--+---+
               |                     |                              |   |
               |                     +------------<-----------------+   |
               |                                                        |
               |                                  +---------<--------+  |
               |                                  |                  |  |
               +--(:CENTER)-----|center posn|-----+--|radius|--------+--+
               |                                  |                  |  |
               |                                  +--|position|------+  |
               |                                                        |
               |             +-----------------<----------------------+ |
               |             |                                        | |
               +--(:TAN_CEN)-+-|element with position|-|center posn|--+-+
               |                                                        |
               |               +--------------------<-----------------+ |
               |               |                                      | |
               +--(:TAN_PT_PT)-+--|element|---|pos|---+-|radius|---+--+-+
               |                                      |            |    |
               |                                      +-|position|-+    |
               |                                                        |
               |             +----------------------<-----------------+ |
               |             |                                        | |
               +--(:TAN2_PT)-+--|1st elem|-|2nd elem|-+-|radius|---+--+-+
               |                                      |            |    |
               |                                      +-|position|-+    |
               |                                                        |
               |                +----------<----------+                 |
               |                |                     |                 |
               +--(:TAN3)-------+--|1st element|---+  |                 |
               |                                   v  |                 |
               |                +--|2nd element|---+  |                 |
               |                |                     |                 |
               |                +--|3rd element|------+--------->-------+
               |                                                        |
               |                +----------<----------+                 |
               |                |                     |                 |
               +--(:3_POS)------+--|1st position|--+  |                 |
               |                                   v  |                 |
               |                +--|2nd position|--+  |                 |
               |                |                     |                 |
               |                +--|3rd position|-----+--------->-------+
               |                                                        |
               |                 +---------<-----------+                |
               |                 |                     |                |
               +--(:DIAMETER)----+--|1st position|--+  |                |
               |                                    |  |                |
               |                 +--|2nd position|--+  |                |
               |                 v                     |                |
               |                 +---------------------+-------->-------+
               |                                                        |
               |                                +----------<----------+ |
               |                                |                     | |
               +--(:CEN_DIA)--|center position|-+--|peripheral posn|--+-+
               |                                |                     | |
               |                                +--|diameter length|--+ |
               |                                                        |
               |                 +---------------------------+          |
               |                 |                           |          |
               +--(:2_POS_RAD)---+--|1st position|--+        |          |
                                                    |        |          |
                                 +-------<----------+        |          |
                                 |                           |          |
                                 |  +-|2nd posn|----+        |          |
                                 |  |               |        |          |
                                 |  | +---<---------+        |          |
                                 |  | |                      |          |
                                 |  | +-|radius len|-->---+  ^          ^
                                 |  |                     |  |          |
                                 +--+                     |  |          |
                                    |                     v  |          |
                                    +---|radius len|-+    |  |          |
                                                     |    |  |          |
                                      +-----<--------+    |  |          |
                                      |                   |  |          |
                                      +-|2nd posn|--->----+  |          |
                                                          |  |          |
                                      +--------<----------+  |          |
                                      |                      |          |
                                      +->-|side position|----+----------+

Options

The following options are available to create your circle.

:CEN_RAD - specifies a center point and a radius either directly, or using a peripheral point at the required distance from the center point. You must define a new center point for each construction circle you create.
:CONCENTRIC - specifies a circular element to be concentric to. You can define a positive or negative offset.
:RADIUS - creates construction circles of a specific radius, at a series of center positions.
:CENTER - creates construction circles of defined diameters around a specific center point.
:TAN_CEN - specifies the center of the construction circle, its radius, and an element to be tangent to.
:TAN_PT_PT - specifies two elements to be tangent to, and either the radius or a peripheral point. If either or both of your elements are B-splines, you can only enter a radius.
:TAN2_PT - specifies 2 positions the construction circle must pass through, its radius, and an element to be tangent.
:TAN3 - specifies three elements the construction circle must be tangent to.
:3_POS - specifies three peripheral points through which the construction circle must pass.
:DIAMETER - specifies two peripheral points which must lie on the diameter of the construction circle.
:CEN_DIA - specifies the center point and the diameter for the circle.
:2_POS_RAD - specifies the radius for the circle and two points which must lie on the diameter of the circle.

When to use

Use this action to create construction circles anywhere on the active workplane.

Example

Enter C_CIRCLE and specify the creation method, location of the center, and the size of the construction circle as follows:

C_CIRCLE :CEN_RAD 100,100 50