Security
This version contains several security enhancements. Updating to this version of the product is strongly recommended.
|
QuickClient / Update Rate / Read-Only Mode
• Added the ability to launch the Quick Client from the project tree for channels, devices, and tag groups.
• Fixed a performance issue when handling Float and Double Arrays in Quick Client.
• When a device is set to Simulate, removed the requirement for clients to have the same Update Rate to see the same data.
• When opening the Configuration in read-only mode, a pop-up now informs the user.
|
MaxAgeRead / WriteVQT
• Fixed a possible crash when using MaxAgeRead with Fail on Bad Quality set to Yes.
• Fixed an issue where a WriteVQT could cause a crash.
|
Publishing Improvements
Added the ability to throttle the amount of data sent to ThingWorx using Store and Forward with new properties: Delay Between Publishes and Max Updates Per Publish.
|
Date Comparison
Added support for comparing dates when using derived tags.
|
Relative Time
• Added support for relative time (LTIME, TIME32, TIME) data types for 5x80 controllers.
• Improved stability of controller project uploads over slow networks.
|
Logix Tags
Fixed an issue adding and editing tags in a valid collection of Logix Tags.
|
Double
Fixed an issue decoding a BACnet double received from a BACnet device.
|
Data Change
Fixed an issue where two values could be output per data change under certain circumstances.
|
Updates & Fixes
• Fixed an issue that could impact an integrity poll if the device indicated a buffer overflow.
• Improved handling of secure authentication requests.
• Fixed an issue that could result in a runtime crash.
• Improved data handling when a session is closed before the end of the frame is received.
• Fixed a possible memory leak during handling of select and operate or data set control objects if the data set was not in the database.
• Improved behavior when shutting down and closing sessions.
• Fixed an issue where tags that get stranded in the middle of a polling cycle would never get released and not poll again.
|
Updates & Fixes
• Fixed an issue that could impact an integrity poll if the device indicated a buffer overflow.
• Improved handling of secure authentication requests.
• Fixed an issue that could result in a runtime crash.
• Improved data handling when a session is closed before the end of the frame is received.
• Fixed a possible memory leak during handling of select and operate or data set control objects if the data set was not in the database.
• Improved behavior when shutting down and closing sessions.
• Fixed an issue where tags that get stranded in the middle of a polling cycle would never get released and not poll again.
|
VCone Meter
Corrected EFM Exporter output for VCone Meter type.
|
Enron Data Types
Fixed a memory issue when using Enron-specific data types.
|
Closing Sessions
Improved behavior when shutting down and closing sessions or sectors.
|
Closing Sessions
Improved behavior when shutting down and closing sessions or sectors.
|
Tag Address
Fixed an issue generating tags from a SCL file that contained periods in the address.
|
iQ-R Model
Fixed an issue with the iQ-R model reading tags with large addresses.
|
Port Closure
Fixed an issue where the driver could fail to recognize a port closure.
|
Timeout
Fixed an issue timing out when the PLC connects, but refuses the request.
|
Schema Updates
• Added support for MTConnect v1.1-1.6 and 2.0 with XML 1.0 schema validation enabled or disabled.
• Added support for MTConnect v1.7 and 1.8 with schema validation disabled.
|
Special Characters
Fixed an issue with browsing for and importing tags with special characters (e.g. O2).
|
Initial Update Timeout
• Added the property Initial Update Timeout to specify the amount of time to wait for the initial tag timeout when interacting with the UA server.
• Fixed an issue with browsing for and importing tags with special characters (e.g. O2).
• Removed read-before-write behavior introduced in 6.9.572 to allow writing to write-only tags.
|
Communication
Fixed an issue that could lead to communication loss.
|
New MIDs / Tag Quality
• Added support for User Data MIDs 240-243.
• Added support for Trace Curve Data MIDs 900-901.
• Added the NewData tag for MID 1201 (Operation result overall data) and MID 1202 (Operation result object data).
• Fixed an issue with tags staying good quality when the tool gets disconnected from the device.
|
Large Tag Counts
Fixed an issue where data was not being handled for larger tag counts using unsolicited communications.
|