Piping > Drawings > Isometric Drawing Generation (ISOGEN) > Example: ISOGEN Attribute Map File for Mapping Bending Data Attributes to ISOGEN Attributes(Spec-Driven Piping)
  
Example: ISOGEN Attribute Map File for Mapping Bending Data Attributes to ISOGEN Attributes(Spec-Driven Piping)
Default Path
<Creo load directory>/text/piping_data/isodata/isogen_attribute_map.csv
If you want more than one set of bending data to be shown on a piece drawing, you can add multiple entries for the same bending data attributes, which point to different ISOGEN attributes.
 
* The number of bending data sets that can be shown on a piece drawing depends on the number of ISOGEN user definable attributes supported by ISOGEN. ISOGEN allows a maximum of 100 such attributes.
The ISOGEN Attribute Map File for mapping bending data attributes to ISOGEN Attributes is as shown in the next table.
PROE_ATTRIBUTE
ISOGEN_ATTRIBUTE
Values for spool
START_FLANGE_TWIST_ANGLE
ATTRIBUTE10
0
START_NODE_NUMBER
ATTRIBUTE11
1
START_FLANGE_ANGLE
ATTRIBUTE12
0
START_BENDING_POINT_1
ATTRIBUTE13
1325
START_BENDING_ANGLE_1
ATTRIBUTE14
90
START_BENDING_ROTATE_ANGLE_1
ATTRIBUTE15
180
START_BENDING_RADIUS_1
ATTRIBUTE16
560
START_BENDING_POINT_2
ATTRIBUTE17
1943.646
START_BENDING_ANGLE_2
ATTRIBUTE18
90
START_BENDING_ROTATE_ANGLE_2
ATTRIBUTE19
0
START_BENDING_RADIUS_2
ATTRIBUTE20
560
START_PIPE_CUT_LENGTH
ATTRIBUTE21
4697.292
END_FLANGE_TWIST_ANGLE
ATTRIBUTE22
0
END_NODE_NUMBER
ATTRIBUTE23
2
END_FLANGE_ANGLE
ATTRIBUTE24
0
END_BENDING_POINT_1
ATTRIBUTE25
535
END_BENDING_ANGLE_1
ATTRIBUTE26
90
END_BENDING_ROTATE_ANGLE_1
ATTRIBUTE27
180
END_BENDING_RADIUS_1
ATTRIBUTE28
560
END_BENDING_POINT_2
ATTRIBUTE29
1943.646
END_BENDING_ANGLE_2
ATTRIBUTE30
90
END_BENDING_ROTATE_ANGLE_2
ATTRIBUTE31
0
END_BENDING_RADIUS_2
ATTRIBUTE32
560
END_PIPE_CUT_LENGTH
ATTRIBUTE33
4697.292
START_FLANGE_TWIST_ANGLE
ATTRIBUTE34
0
START_NODE_NUMBER
ATTRIBUTE35
3
START_FLANGE_ANGLE
ATTRIBUTE36
0
START_BENDING_POINT_1
ATTRIBUTE37
577.3
START_BENDING_ANGLE_1
ATTRIBUTE38
90
START_BENDING_ROTATE_ANGLE_1
ATTRIBUTE39
0
START_BENDING_RADIUS_1
ATTRIBUTE40
265
START_PIPE_CUT_LENGTH
ATTRIBUTE41
2227.161
END_FLANGE_TWIST_ANGLE
ATTRIBUTE42
0
END_NODE_NUMBER
ATTRIBUTE43
4
END_FLANGE_ANGLE
ATTRIBUTE44
0
END_BENDING_POINT_1
ATTRIBUTE45
1226.6
END_BENDING_ANGLE_1
ATTRIBUTE46
90
END_BENDING_ROTATE_ANGLE_1
ATTRIBUTE47
0
END_BENDING_RADIUS_1
ATTRIBUTE48
265
END_PIPE_CUT_LENGTH
ATTRIBUTE49
2227.161
START_FLANGE_TWIST_ANGLE
ATTRIBUTE50
0
START_NODE_NUMBER
ATTRIBUTE51
5
START_FLANGE_ANGLE
ATTRIBUTE52
0
START_BENDING_POINT_1
ATTRIBUTE53
1339.2
START_BENDING_ANGLE_1
ATTRIBUTE54
90
START_BENDING_ROTATE_ANGLE_1
ATTRIBUTE55
0
START_BENDING_RADIUS_1
ATTRIBUTE56
345
START_PIPE_CUT_LENGTH
ATTRIBUTE57
3335.125
END_FLANGE_TWIST_ANGLE
ATTRIBUTE58
0
END_NODE_NUMBER
ATTRIBUTE59
6
END_FLANGE_ANGLE
ATTRIBUTE60
0
END_BENDING_POINT_1
ATTRIBUTE61
1446
END_BENDING_ANGLE_1
ATTRIBUTE62
90
END_BENDING_ROTATE_ANGLE_1
ATTRIBUTE63
0
END_BENDING_RADIUS_1
ATTRIBUTE64
345
END_PIPE_CUT_LENGTH
ATTRIBUTE65
3335.125
START_FLANGE_TWIST_ANGLE
ATTRIBUTE66
0
START_NODE_NUMBER
ATTRIBUTE67
7
START_FLANGE_ANGLE
ATTRIBUTE68
0
START_BENDING_POINT_1
ATTRIBUTE69
1139.2
START_BENDING_ANGLE_1
ATTRIBUTE70
90
START_BENDING_ROTATE_ANGLE_1
ATTRIBUTE71
-90
START_BENDING_RADIUS_1
ATTRIBUTE72
345
START_BENDING_POINT_2
ATTRIBUTE73
1441.925
START_BENDING_ANGLE_2
ATTRIBUTE74
90
START_BENDING_ROTATE_ANGLE_2
ATTRIBUTE75
0
START_BENDING_RADIUS_2
ATTRIBUTE76
345
START_PIPE_CUT_LENGTH
ATTRIBUTE77
4577.049
END_FLANGE_TWIST_ANGLE
ATTRIBUTE78
0
END_NODE_NUMBER
ATTRIBUTE79
8
END_FLANGE_ANGLE
ATTRIBUTE80
0
END_BENDING_POINT_1
ATTRIBUTE81
1446
END_BENDING_ANGLE_1
ATTRIBUTE82
90
END_BENDING_ROTATE_ANGLE_1
ATTRIBUTE83
90
END_BENDING_RADIUS_1
ATTRIBUTE84
345
END_BENDING_POINT_2
ATTRIBUTE85
1441.925
END_BENDING_ANGLE_2
ATTRIBUTE86
90
END_BENDING_ROTATE_ANGLE_2
ATTRIBUTE87
0
END_BENDING_RADIUS_2
ATTRIBUTE88
345
END_PIPE_CUT_LENGTH
ATTRIBUTE89
4577.049
The first two columns in this table are a part of the isogen_attribute map.csv file. The last column shows typical values for a spool and is not a part of the isogen_attribute map.csv file, but is included for better clarity.
In the previous table isogen_attribute_map.csv file, bending data of the spool can be viewed in the following four parts:
• Attributes between 10 and 33 represent bending data for pipe bends that appear between node number 1 ( a pipe start represented by Attribute 11) and node number 2 (an entry point of reducer represented by Attribute 23)
• Attributes between 34 and 49 represent bending data for pipe bends that appear between node number 3 (exit point of reducer represented by Attribute 35) and node number 4 (an entry point of TEE fitting represented by Attribute 43)
• Attributes between 50 and 65 represent bending data for pipe bends that appear between node number 5 (right exit of reducer represented by Attribute 51) and node number 6 (right end of the pipe represented by Attribute 59)
• Attributes between 66 and 89 represent bending data for pipe bends that appear between node number 7 (left exit of reducer represented by Attribute 67) and node number 8 (left end of the pipe represented by Attribute 79)
 
* Use the isogen_attribute_map_file configuration option to access the modified isogen_attribute map.csv file present in your local directory.