DA_PP_CONTOUR_SET allows modification of the contour display settings.
*9* Only available if Von Mises stress is selected for contour display and the
assigned material contains value for failure strength
-->DA_PP_CONTOUR_SET----+
|
+-----------------------+
|
+---+---+--(:DA_RESULT)-------------|SELECT S_FERRUM_RESULT|---+-->
| | |
| +--(:DA_CONTOUR_COLORRANGE)---+--(:RED_TO_BLUE)----+---+
| | | | |
| | +--(:WHITE_TO_BLUE)--+ |
| | | | |
| | +--(:GRAY_SHADES)----+ |
| | | | |
| | +--(:STRIPES)--------+ |
| | |
| +--(:DA_MIN_VAL)--------------|number|-----------------+
| | |
| +--(:DA_MAX_VAL)--------------|number|-----------------+
| | |
| +--(:DA_SECURITY_FACTOR)------|number|---------(*9*)---+
^ | |
| +--(:DA_INTERVAL)-------------|number|-----------------+
| | |
| +--(:DA_NUM_COLORS)-----------|number|-----------------+
| | |
| +--(:DA_RANGE_METHOD)----------+--(:MIN_MAX)--------+--+
| | | | |
| | +--(:MIN_INTERVAL)---+ |
| | | | |
| | +--(:MAX_INTERVAL)---+ |
| | | | |
| | +--(:FULL_RANGE)-----+ |
| | | | |
| | +--(:FROM_MATRL)(*9*)+ |
| | |
| +--(:DA_DISPLAY_METHOD)--------+--(:CONTIN)-------+----+
^ | | | |
| | +--(:NON_CONTIN)---+ |
| | |
| +--(:DA_DRAW_EDGES)------------+---(:ON)----+----------+
| | | | |
| | +---(:OFF)---+ |
| | |
| +--(:DA_CONTOUR_AVERAGING)-----+---(:ON)----+----------+
| | | | |
| | +---(:OFF)---+ |
| | |
| +--(:DA_UPDATE_DISPLAY)--------------------------------+
| |
+--------<-----------<----------<---------<-----------<----+
The following options are available to set contour display options.
-
:DA_CONTOUR_COLORRANGE
- enables selection of the range of colors to use for the results range.
-
:RED_TO_BLUE
- selects a range of colors from red to blue.
-
:WHITE_TO_BLUE
- selects a range of colors from white to blue.
-
:GRAY_SHADES
- selects shades of gray.
-
:STRIPES
- selects contrasting stripes.
-
:DA_MIN_VAL
- sets minimum value for results to be displayed. Enabled with :DA_RANGE_METHOD
set to :MIN_MAX
or :MIN_INTERVAL
.
-
:DA_MAX_VAL
- sets maximum value for results to be displayed. Enabled with :DA_RANGE_METHOD
set to :MIN_MAX
or :MAX_INTERVAL
.
-
:DA_INTERVAL
- sets an interval between results to be displayed. Enabled with :DA_RANGE_METHOD
set to :MAX_INTERVAL
or :MIN_INTERVAL
.
-
:DA_SECURITY_FACTOR
- sets the material safety factor (failure strength).
-
:DA_NUM_COLORS
- sets the number of color contours to use.
-
:DA_RANGE_METHOD
- enables selection of the range method for contour display.
-
:MIN_MAX
- sets the range type to the minimum and maximum result values.
-
:MIN_INTERVAL
- sets the range type to a minimum result value and an interval.
-
:MAX_INTERVAL
- sets the range type to a maximum result value and an interval.
-
:FULL_RANGE
- sets the range type to the full range of results in the selected results component.
-
:DA_DRAW_EDGES
- toggles the display of element edges.
-
:DA_CONTOUR_AVERAGING
- toggles averaging of results across the mesh elements.
-
:DA_UPDATE_DISPLAY
- updates the results window according to the selected contour display options.
Use this action when setting contour display options in Design Integrity.
DA_PP_DEFORMED_SET terminate action,
DA_PP_SYMBOLS_SET terminate action
DA_PP_RESULTS terminate action