CoCreate OneSpace Designer - Commands Reference Manual

POSITION_WP_SA repositions existing workplanes.

Syntax

---->(POSITION_WP_SA)----+
                         |
     +----------<--------+
     |
     |             +-------------<-----------+
     |             |                         |
     +--(:PAR_WP)--+--(:REF_WP)--|wp|--------+
     |             |                         |
     |             +--(:OFFSET)--|distance|--+
     |             |
     |             +--(:DONE)------------------------------->--------+---->
     v                                                               |
     |                                                               |
     |              +-----------<----------------------+             |
     |              |                                  |             |
     +--(:NORM_WP)--+--(:REF_WP)--|wp|-----------------+             |
     |              |                                  |             ^
     |              +--(:ORIGIN)--|point 3d|-----------+             |
     |              |                                  |             |
     |              +--(:NORMAL)--|MEASURE_DIR_3D_SA|--+             |
     |              |                                                |
     v              +--(:DONE)------------------------------>--------+
     |                                                               |
     |                                                               |
     |               +------------<--------------------+             |
     |               |                                 |             ^
     +--(:PAR_FACE)--+--(:FACE)--|pt on face|----------+             |
     |               |                                 |             |
     |               +--(:OFFSET)--|distance|----------+             |
     |               |                                 |             |
     |               +--(:FACE_PT)--|pt on face|-------+             |
     |               |                                 |             |
     |               +--(:U_DIR)--|MEASURE_DIR_3D_SA|--+             |
     |               |                                 |             |
     |               +--(:SLIDE_ORIGIN)--|point 3d|----+             |
     |               |                                               |
     v               +--(:DONE)----------------------------->--------+
     |                                                               |
     |               +------------<---------------------+            |
     |               |                                  |            ^
     +--(:PT_DIR)----+--(:ORIGIN)--|point 3d|-----------+            |
     |               |                                  |            |
     |               +--(:NORMAL)--|MEASURE_DIR_3D_SA|--+            |
     |               |                                  |            |
     |               +--(:U_DIR)---|MEASURE_DIR_3D_SA|--+            |
     |               |                                               |
     v               +--(:DONE)----------------------------->--------+
     |                                                               |
     +--(:PT_PT_PT)--|origin|--|point on U axis|--|point on V axis|--+
     |                                                               |
     |                                                               |
     +--(:MATCH_3PT)--|fixed pt 1|--|move pt 1|--+                   ^
     |                                           |                   |
     |    +-------------------<------------------+                   |
     v    |                                                          |
     |    +--|fixed pt 2|--|move pt 2|--|fixed pt 3|--|move pt 3|-->-+
     |                                                               |
     |                                                               |
     +--(:TRANSLATE)--+--(:TWO_PTV)--|point 3d| |point 3d|--+--------+
     |                |                                     |        |
     |                +--(:DIR_LEN)--|MEASURE_DIR_3D_SA|----+        |
     |                                                               |
     |             +---------------<----------------+                |
     |             |                                |                ^
     +--(:ROTATE)--+--(:AXIS)--|MEASURE_DIR_3D_SA|--+                |
     |             |                                |                |
     |             +--(:ROTATION_ANGLE)--|angle|----+                |
     v             |                                                 |
     |             +--(:DONE)------------------------>---------------+
     |                                                               |
     |                                                               |
     +--(:DYNAMIC)----------------------------------->---------------+
     |                                                               |
     +--(:WORLD_ORIGIN)------------------------------>---------------+
     |                                                               |
     +--(:SET_KNOBS)--|SET_KNOBS_POSITION_SA|-------->---------------+

Options

• :PAR_WP - specifies a position parallel to a reference workplane.
  • :REF_WP - specifies the reference workplane.
  • :OFFSET - specifies the offset distance from the reference workplane.

• :NORM_WP - specifies a position normal to a reference workplane.
  • :REF_WP - specifies the reference workplane.
  • :ORIGIN - specifies the new 3D location of the workplane.
  • :NORMAL - specifies a 3D direction normal to the reference face.

• :PAR_FACE - specifies a position parallel to a face.
  • :FACE - specifies the face to be parallel to.
  • :OFFSET - specifies the offset distance from the reference face.
  • :FACE_PT - specifies the face to be parallel to.
  • :U_DIR - specifies the U-axis to be parallel to.
  • :SLIDE_ORIGIN - specifies the origin to which the workplane slides to.

• :PT_DIR - specifies a position parallel to a face.
  • :ORIGIN - specifies the origin to be parallel to.
  • :NORMAL - specifies the normal to be parallel to.
  • :U_DIR - specifies the U-direction to be parallel to.

• :PT_PT_PT - specifies a position via three points.
• :MATCH_3PT - specifies three pairs of "fix" and "move" points.
• :TRANSLATE - specifies a 3D vector for translation.
  • :TWO_PTV - the vector direction is the direction from the first point to the second point; the vector magnitude is the distance between the two points.
  • :DIR_LEN - the vector direction and magnitude are defined directly.

• :ROTATE - rotates the specified workplane.
  • :AXIS - specifies the axis to be rotated around.
  • :ROTATION_ANGLE - specifies the angle of rotation.

• :DYNAMIC - lets you use the knob box to dynamically reposition the specified workplane.
• :WORLD_ORIGIN - positions the specified workplane at the world origin.
• :SET_KNOBS - specifies the behavior of knobs for dynamic positioning.

When to use

See also