About Sheet Metal Parameters
Sheet metal parameters control the default settings of sheet metal tool properties. Each parameter has a corresponding setting that is displayed in the Model Properties dialog box. Set or modify sheet metal parameters using the Parameters dialog box, or except for thickness, using the Sheetmetal Preferences dialog box.
Set these configuration options to control the behavior of default tool settings:
• smt_drive_tools_by_parameters—To use parameter values as the default values of selected tool settings and to automatically update features when parameter values change.
• smt_drive_bend_by_parameters—To use parameter values to control the default value of bend angle and bend dimension location settings and to automatically update features when parameter values change.
 |
If you want to enable smt_drive_bend_by_parameters, you must also set smt_drive_tools_by_parameters to yes.
|
The following table lists all the sheet metal-specific parameters, their description, and required parameter values:
|
|
Bend allowance in an imported legacy parameters file is calculated using the last value of the factor type specified for the part.
|
|
Parameter Name
|
Description
|
Value
|
|---|---|---|
|
SMT_THICKNESS
|
Sets the thickness of sheet metal walls.
|
Numeric value
|
|
SMT_PART_BEND_ALLOWANCE_FACTOR
|
Sets the value of Y factor or K factor.
|
Numeric value
|
|
SMT_PART_BEND_ALLOW_FACTOR_TYPE
|
Sets Y factor or K factor as the bend allowance factor type.
|
K Factor
Y Factor
|
|
SMT_PART_BEND_TABLE_NAME
|
Sets the bend table assigned to calculate developed length of geometry with arcs.
|
Name
|
|
SMT_DFLT_BEND_RADIUS
|
Sets the radius of bends.
|
Numeric value
|
|
SMT_DFLT_RADIUS_SIDE
|
Defines the dimension location scheme of bends.
|
Inside
Outside
|
|
SMT_DFLT_BEND_ANGLE
|
Defines the value of bend angles.
|
Numeric value
|
|
SMT_DFLT_CRNR_REL_TYPE
|
Sets the type of corner relief.
|
Circular
No Relief
Normal
Obround
Rectangular
Square
V Notch
|
|
SMT_DFLT_CRNR_REL_WIDTH
|
Sets the width of corner relief.
|
Numeric value
|
|
SMT_DFLT_CRNR_REL_DEPTH_TYPE
|
Sets the depth type of corner relief.
|
Blind
On Origin
Up to Bend
|
|
SMT_DFLT_CRNR_REL_DEPTH
|
Sets the depth dimension of circular, rectangular, and obround corner relief.
|
Numeric value
|
|
SMT_DFLT_BEND_REL_TYPE
|
Sets the type of bend relief.
|
No Relief
Obround
Rectangular
Rip
Stretch
|
|
SMT_DFLT_BEND_REL_WIDTH
|
Sets the width of bend relief.
|
Numeric value
|
|
SMT_DFLT_BEND_REL_DEPTH_TYPE
|
Sets the depth type of bend relief.
|
Blind
Tangent to Bend
Up to Bend
|
|
SMT_DFLT_BEND_REL_DEPTH
|
Defines the depth dimension of circular, rectangular, and obround bend relief.
|
Numeric value
|
|
SMT_DFLT_BEND_REL_LENGTH_TYPE
|
Sets the default length type of bend relief.
|
Through All
To Next
Blind
|
|
SMT_DFLT_BEND_REL_LENGTH
|
Defines the length dimension of rectangular and obround bend relief for the Blind length type.
|
Numeric value
|
|
SMT_DFLT_BEND_REL_ANGLE
|
Defines the angle of stretch bend relief.
|
Numeric value
|
|
SMT_GAP
|
Defines the dimension of the gap for overlapping edges, seams, and miter cuts.
|
Numeric value
|
|
SMT_DFLT_EDGE_TREA_TYPE
|
Defines the type of seams.
|
Blind
Gap
Open
Overlap
|
|
SMT_DFLT_EDGE_TREA_WIDTH
|
Sets the width of seams.
|
Numeric value
|
|
SMT_DFLT_MITER_CUT_WIDTH
|
Sets the width of miter cuts.
|
Numeric value
|
|
SMT_DFLT_MITER_CUT_OFFSET
|
Defines the offset dimension of miter cuts.
|
Numeric value
|