Standard Hole Parameters
When you create a standard Hole feature, it includes the parameters listed in the following tables. These are read-only system parameters, whose values are taken from the hole chart. To add user-defined parameters to the hole chart, see Hole Charts.
You can view the parameters by right-clicking a hole in the Model Tree and choosing either 
Parameters or 
Information > 
Feature Information. The parameters also appear on the Properties tab of the Hole tool.
Parameters or Information > Feature Information. The parameters also appear on the Properties tab of the Hole tool.Some of the parameters are available only when specific options are set.
Parameters common to all hole types | Description |
|---|---|
BOTCSINK_ANGLE | Bottom countersink angle. |
BOTCSINK_DIAM | Bottom countersink diameter. |
CBORE_DEPTH | Counterbore depth. |
CBORE_DIAMETER | Counterbore diameter. |
CLASS | Tolerance class of the hole as defined in the hole chart. |
CSINK_ANGLE | Countersink angle. |
CSINK_DIAMETER | Countersink diameter. |
DRILL_DEPTH | Drill depth of blind hole. |
METRIC | • YES for models that use metric units. • NO for models that do not use metric units. |
PITCH | Pitch (the distance between threads). |
SCREW_SIZE | Unique identifier of the hole, as defined in the FASTENER_ID column in the hole chart. |
THREAD_DEPTH | Blind depth of the threaded part of the hole. |
THREAD_LENGTH | Length of the threaded part of the hole. |
THREAD_SERIES | Name of the hole thread series (ISO, UNC, UNF, NPT, NPTF, ISO_7-1). |
THREADS_PER_INCH | Number of threads per inch. |
Additional parameters in straight holes | Description |
|---|---|
DRILL_DIAMETER | Drill diameter of straight hole. |
DRILL_POINT_ANGLE | Tip angle of straight hole with blind depth. |
THREAD_DIAMETER | Thread diameter of straight hole. |
Additional parameters in tapered holes | Description |
|---|---|
HANDTIGHT_LENGTH | Distance that a pipe thread can be screwed into a fitting by hand before it jams. |
MAJOR_DIAM_END | Diameter of the largest part of a thread across the bottom of the thread. |
MAJOR_DIAM_START | Diameter of the largest part of a thread across the top of the thread. |
MINOR_DIAM_END | Diameter of the smallest part of a thread across the bottom of the thread. |
MINOR_DIAM_START | Diameter of the smallest part of a thread across the top of the thread. |
PERCENT_THREAD | Ratio describing the actual engagement of fastener threads. |
PIPE_OD | Outside diameter of a pipe of the same nominal size. |
PITCH_DIAM_END | Bottom of a cylinder along the threading whose diameter is half the distance between the crest and the root of the threading. |
PITCH_DIAM_START | Top of a cylinder along the threading whose diameter is half the distance between the crest and the root of the threading. |
STRAIGHT_DEC | Diameter of straight drill. |
STRAIGHT_DEPTH | Depth of straight drill. Available for tapered holes with blind depth option of straight drill. |
STRAIGHT_TIP_ANGLE | Tip angle of a straight drill. Available for tapered holes with blind depth option of straight drill. |
TAPER_ANGLE | Angle between the smaller and larger diameter along the length of a taper. |
TAPERED_TIP_ANGLE | Tip angle of a tapered hole. |
THREAD | Number of threads per inch. |
THREAD_ANGLE | Angle between the sides of a screw thread, measured in an axial plane. |
THREAD_HEIGHT | Distance between the minor and major thread diameters measured along the radius. |
TOOTH_RADIUS | Radius of the rounding at the thread crest (at the tip of each tooth) or thread root (between teeth). Available for tapered holes that use ISO data. |
WASHOUT_ANGLE | Angle between the surface at the point that threading begins, and the thread root at the point at which the threading achieves its full depth, over the length of the washout thread. |
WRENCHING_LENGTH | Distance that a pipe thread can be screwed into a fitting using a wrench before it jams. |