![[Books]](books.gif)
|
MACH_ADV_LIBRARY_THREADED_THROUGHHOLE creates, copies, or modifies a Threaded Through Hole
->-(MACH_ADV_LIBRARY_THREADED_THROUGHHOLE)-->------>------->------->------->------->------->------->------->------->------->----\
|
/--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----/
|
| /-->---- (:action) ->- (:modify) ->- (:feature_id) ...... (:action) -> (:initialized) ->----------->----\
| | |
\--->---+-->------->------->------->------->------->------->------->------->------->------->------->------->----+-->----\
| | |
\-->---- (:action) ->- (:copy) ->- (:feature_id) ...... (:action) -> (:initialized) ->----->------->----/ |
|
|
/--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----/
|
| /--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----\
| | |
\--->---+-->--(:SEL_FACE)-->------->------|face|-->-------->------->------->------->------->------->------->----+-->----
| |
+-->--(:CEN_PNT)-->-------->------|point 3d|-->---->------->------->------->------->------->------->----+
| |
+-->--(:AXIS)-->--->------->------|measure_axis_3d_sa|----->------->------->------->------->------->----+
| |
+-->--(:TAP_UNITS)-->-- [ :metric | :inch | :BSW | :BSF | :BSP |
| | :UNC | :UNF | :NPT |
| | :PIPE_RP | :PIPE_G |
| | :TRAPEZOID | :FLAT_TRAPEZOID |
| | :SAW |
| | :ROUND | :ROUND_MINING |
| | :EDISON ]-->--->------->------->------->------->------->----+
| |
+-->--(:THREAD_DIA)-->----->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:THREAD_SIZE)-->---->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:THREAD_TPI)--->---->------|number|-->------>------->------->------->------->------->------->----+
| |
+-->--(:THREAD_STARTS)----->------|number|-->------>------->------->------->------->------->------->----+
| |
+-->--(:THREAD_HAND)-->---->------[ :right | :left ]------->------->------->------->------->------->----+
| |
+-->--(:NOMINAL_PIPE_DIA)-->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:DRILL_DIA)-->------>------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:DRILL_DEPTH)-->---->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:CHAMFER_DEPTH)----->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:CHAMFER_ANGLE)----->------|angle|-->------->------->------->------->------->------->------->----+
| |
+-->--(:BACK_CHAMFER_DEPTH)-->----|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:BACK_CHAMFER_ANGLE)-->----|angle|-->------->------->------->------->------->------->------->----+
| |
+-->--(:NAME)---------->--->------|name|------------------->------->------->------->------->------->----+
| |
+-->--(:FLAG_DP)-------+--->------|docuplane|------>---+--->------->------->------->------->------->----+
| | | |
| \--->------[ :on | :off ] -->---/ |
| |
+-->--(:DRILL_DIA_SAFETY_ZONE_THICKNESS)--------+--->------|length|-------->---+--->------->------->----+
| | | |
| \--->------[ :on | :off ] ->---/ |
| |
+-->--(:IMAGE_SHOWN)-->---->------->------->------->------->------->------->------->------->------->----+
| |
+-->--(:TOLERANCE_AND_QUALITY)----->------->------->------->------->------->------->------->------->----+
| |
\-->--(:NEXT)-->--->------->------->------->------->------->------->------->------->------->------->----/
The following options are available to create, copy or modify a Threaded Through Hole
| Option | Description | ||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| :SEL_FACE | The Face which contains the "Start Point" of the drill operation. If you pick the Face, Center Point and Axis will be derived from the pick too. | ||||||||||||||||||||||||||||||
| :CEN_PNT | The "Start Point" of the drill operation. It will be identified by a position upon a face on creation. It may be left hanging in space later, if the start face is deleted later by other OneSpace Designer operations. If you pick the Face the Center Point will be derived from the pick too. | ||||||||||||||||||||||||||||||
| :AXIS | The "Axis" of the hole. It will be identified by a position upon a face on creation. It may be left hanging in space later, if the start face is deleted later by other OneSpace Designer operations. If you pick the Face the Axis will be derived from the pick too (i.e. the face normal calculated at the picked position). | ||||||||||||||||||||||||||||||
| :TAP_UNITS |
switches the thread definitions :
:inch, if you have set an imperial length unit.
|
||||||||||||||||||||||||||||||
| :THREAD_DIA | The nominal diameter of the thread | ||||||||||||||||||||||||||||||
| :THREAD_SIZE | The pitch of the thread | ||||||||||||||||||||||||||||||
| :THREAD_TPI | Alternative method to specify the pitch of the thread by entering the Thread Per Inch value for all imperial style threads and pipe threads. | ||||||||||||||||||||||||||||||
| :THREAD_STARTS | The number of thread starts. This value has no effect upon the geometrical representation of the threaded hole, but the data is needed for complete specification of the thread in order to create correct manufacturing documents. The default is 1. | ||||||||||||||||||||||||||||||
| :THREAD_HAND | The direction of the thread. This value has no effect upon the geometrical
representation of the threaded hole, but the data is needed for complete
specification of the thread in order to create correct manufacturing
documents. The following keywords are possible :
|
||||||||||||||||||||||||||||||
| :NOMINAL_PIPE_DIA | The nominal diameter of a pipe thread, which is not the "outer" diameter of the thread. This value has no effect upon the geometrical representation of the threaded hole, but the data is needed for complete specification of the pipe thread in order to create correct manufacturing documents. | ||||||||||||||||||||||||||||||
| :DRILL_DIA | The diameter of the hole to be drilled. | ||||||||||||||||||||||||||||||
| :DRILL_DEPTH | The drilled depth in terms of a technical drawing, i.e. the depth is the "height" of the created cylinder not the in-feed distance of the drill tool if it is not a "Flat Hole". | ||||||||||||||||||||||||||||||
| :CHAMFER_DEPTH | The depth of the chamfer measured in direction of the axis | ||||||||||||||||||||||||||||||
| :CHAMFER_ANGLE | The tool tip angle of the sink tool. | ||||||||||||||||||||||||||||||
| :BACK_CHAMFER_DEPTH | The depth of the backside chamfer measured in direction of the axis | ||||||||||||||||||||||||||||||
| :BACK_CHAMFER_ANGLE | The tool tip angle of the sink tool. | ||||||||||||||||||||||||||||||
| :NAME | the name which the feature will get after its creation. This parameter is only available when creating or copying a feature. | ||||||||||||||||||||||||||||||
| :FLAG_DP | The docuplane which should own the flag text.
If you switch on the variable for the first time within a dialog, the computed defaults will be activated. If you decide not to use the docuplane for the flag text but want to get a free flag text, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again |
||||||||||||||||||||||||||||||
| :DRILL_DIA_SAFETY_ZONE_THICKNESS | The thickness of the diameter related safety zone (i.e. the wall thickness of the "pipe" around the hole) If you decide not to use the safety zone, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again. |
||||||||||||||||||||||||||||||
| :IMAGE_SHOWN | Will hide a displayed parameter image or display a hidden parameter image | ||||||||||||||||||||||||||||||
| :TOLERANCE_AND_QUALITY | Will hide displayed input fields for thickness of savety zone or display hidden input fields for thickness of savety zone | ||||||||||||||||||||||||||||||
| :NEXT | Will create, copy or modify the hole and will prompt for the next location in create and copy modes while asking for selection of the next feature of the same type in the modify mode |
|