![[Books]](books.gif)
|
MACH_ADV_LIBRARY_COUNTERSUNK_PARTIALLY_TOLERANCED_FLAT_BLINDHOLE creates, copies, or modifies a Countersunk Partially Toleranced Flat Blind Hole
->-(MACH_ADV_LIBRARY_COUNTERSUNK_PARTIALLY_TOLERANCED_FLAT_BLINDHOLE)-->----------->------->------->------->------->------->----\
|
/--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----/
|
| /-->---- (:action) ->- (:modify) ->- (:feature_id) ...... (:action) -> (:initialized) ->----------->----\
| | |
\--->---+-->------->------->------->------->------->------->------->------->------->------->------->------->----+-->----\
| | |
\-->---- (:action) ->- (:copy) ->- (:feature_id) ...... (:action) -> (:initialized) ->----->------->----/ |
|
|
/--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----/
|
| /--<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<-------<----\
| | |
\--->---+-->--(:SEL_FACE)-->------->------|face|-->-------->------->------->------->------->------->------->----+-->----
| |
+-->--(:CEN_PNT)-->-------->------|point 3d|-->---->------->------->------->------->------->------->----+
| |
+-->--(:AXIS)-->--->------->------|measure_axis_3d_sa|----->------->------->------->------->------->----+
| |
+-->--(:DRILL_DIA)-->------>------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:DRILL_DIA_TOL)----->------|get_tolerance|-->------->------->------->------->------->------->----+
| |
+-->--(:DRILL_DEPTH)-->---->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:DRILL_DEPTH_TOL)-->-------|get_tolerance|-->------->------->------->------->------->------->----+
| |
+-->--(:TOLERANCE_DEPTH)-->-------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:TOLERANCE_DEPTH_TOL)-->---|get_tolerance|-->------->------->------->------->------->------->----+
| |
+-->--(:CHAMFER_DEPTH)----->------|length|-->------>------->------->------->------->------->------->----+
| |
+-->--(:CHAMFER_ANGLE)----->------|angle|-->------->------->------->------->------->------->------->----+
| |
+-->--(:BOTTOM_SF_QUAL)---->------|get_surface_quality|---->------->------->------->------->------->----+
| |
+-->--(:SIDE_SF_QUAL)-->--->------|get_surface_quality|---->------->------->------->------->------->----+
| |
+-->--(:NAME)---------->--->------|name|------------------->------->------->------->------->------->----+
| |
+-->--(:FLAG_DP)-------+--->------|docuplane|------>---+--->------->------->------->------->------->----+
| | | |
| \--->------[ :on | :off ] -->---/ |
| |
+-->--(:DIA_DP)--------+--->------|docuplane|------>---+--->------->------->------->------->------->----+
| | | |
| \--->------[ :on | :off ] -->---/ |
| |
+-->--(:DEPTH_DP)------+--->------|docuplane|------>---+--->------->------->------->------->------->----+
| | | |
| \--->------[ :on | :off ] -->---/ |
| |
+-->--(:DRILL_DEPTH_SAFETY_ZONE_THICKNESS)------+--->------|length|-------->---+--->------->------->----+
| | | |
| \--->------[ :on | :off ] ->---/ |
| |
+-->--(:DRILL_DIA_SAFETY_ZONE_THICKNESS)--------+--->------|length|-------->---+--->------->------->----+
| | | |
| \--->------[ :on | :off ] ->---/ |
| |
+-->--(:IMAGE_SHOWN)-->---->------->------->------->------->------->------->------->------->------->----+
| |
+-->--(:TOLERANCE_AND_QUALITY)----->------->------->------->------->------->------->------->------->----+
| |
\-->--(:NEXT)-->--->------->------->------->------->------->------->------->------->------->------->----/
The following options are available to create, copy or modify a Countersunk Partially Toleranced Flat Blind Hole
| Option | Description |
|---|---|
| :SEL_FACE | The Face which contains the "Start Point" of the drill operation. If you pick the Face, Center Point and Axis will be derived from the pick too. |
| :CEN_PNT | The "Start Point" of the drill operation. It will be identified by a position upon a face on creation. It may be left hanging in space later, if the start face is deleted later by other OneSpace Designer operations. If you pick the Face the Center Point will be derived from the pick too. |
| :AXIS | The "Axis" of the hole. It will be identified by a position upon a face on creation. It may be left hanging in space later, if the start face is deleted later by other OneSpace Designer operations. If you pick the Face the Axis will be derived from the pick too (i.e. the face normal calculated at the picked position). |
| :DRILL_DIA | The diameter of the hole to be drilled. |
| :DRILL_DEPTH | The drilled depth in terms of a technical drawing, i.e. the depth is the "height" of the created cylinder not the in-feed distance of the drill tool if it is not a "Flat Hole". |
| :TOLERANCE_DEPTH | The toleranced depth in terms of a technical drawing, i.e. the depth is the "height" of the created cylinder not the in-feed distance of the drill tool. |
| :CHAMFER_DEPTH | The depth of the chamfer measured in direction of the axis |
| :CHAMFER_ANGLE | The tool tip angle of the sink tool. |
| :BOTTOM_SF_QUAL | will call the subdialog get_surface_quality in order to fetch the Surface Quality specification for the bottom surface of the hole |
| :SIDE_SF_QUAL | will call the subdialog get_surface_quality in order to fetch the Surface Quality specification for the side surface of the counterbore |
| :NAME | the name which the feature will get after its creation. This parameter is only available when creating or copying a feature. |
| :FLAG_DP | The docuplane which should own the flag text.
If you switch on the variable for the first time within a dialog, the computed defaults will be activated. If you decide not to use the docuplane for the flag text but want to get a free flag text, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again |
| :DIA_DP | The docuplane which should own the diameter related dimensions.
If you switch on the variable for the first time within a dialog, the computed defaults will be activated. If you decide not to use the docuplane for the dimensions but want to get a free dimensions, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again |
| :DEPTH_DP | The docuplane which should own the depth related dimensions.
If you switch on the variable for the first time within a dialog, the computed defaults will be activated. If you decide not to use the docuplane for the dimensions but want to get a free dimensions, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again |
| :DRILL_DEPTH_SAFETY_ZONE_THICKNESS | The thickness of the depth related safety zone (i.e. the wall thickness of the bottom) If you decide not to use the safety zone, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again. |
| :DRILL_DIA_SAFETY_ZONE_THICKNESS | The thickness of the diameter related safety zone (i.e. the wall thickness of the "pipe" around the hole) If you decide not to use the safety zone, simply switch off the variable. You can reactivate your last value (within the same dialog) later by switching it on again. |
| :IMAGE_SHOWN | Will hide a displayed parameter image or display a hidden parameter image |
| :TOLERANCE_AND_QUALITY | Will hide displayed tolerance input fields or display hidden tolerance input fields |
| :NEXT | Will create, copy or modify the hole and will prompt for the next location in create and copy modes while asking for selection of the next feature of the same type in the modify mode |
|